Graco
XP70-hf
To-komponent sprøyting gjort enkelt og rimelig.
XP-hf-systemet kombinerer de populære XP70-sprøytene med den kraftige XL 10000 luftmotoren. Ved å kombinere disse to teknologiene får du mer flyt - får jobben raskere og med mindre slitasje. Graco XP70-hf er konstruert for mer flytkapasitet, og er flott for applikasjoner der du vil spraye med flere pistoler eller større dysestørrelser. Fleksible alternativer for blandingsforhold, trykk og strømningshastighet - velg riktig system for applikasjonen. Hvis du av og til skifter materiale, er Graco XP-sprøyter det riktige valget. Det er fordi du kan endre forholdet ved å endre en eller to pumpesenkere. Tilgjengelig i blandingsforholdene 1: 1, 1,5: 1, 2: 1, 2,5: 1, 3: 1 og 4: 1.
Høytrykksytelse for todelt belegg med høyt faststoff.
Redusert materialavfall
Ikke mer kasting av ubrukt blandet materiale på slutten av dagen
Spar penger ved å bruke mindre oppløsningsmiddel
Konsistent materialkvalitet - ikke mer gjetting eller menneskelig feil i måle materialer
Enkel å betjene - minimal trening kreves
Reduserte vedlikeholdskostnader
Vurdert for 500 bar, 50 MPa for 7250 psi for å håndtere tyktflytende materialer og lange slangelengder
| XP and XP-h Proportioners | |
| Maximum Fluid Working Pressure |
See Models section in instruction manual.
|
| Maximum Air/Hydraulic Oil Working Pressure |
See Models section in instruction manual.
|
| Combined Fluid Output (cc/cycle) |
See Models section in instruction manual.
|
| Pressure Ratio |
See Models section in instruction manual.
|
| Fluid Flow at 40 cpm |
See Models section in instruction manual.
|
| Hydraulic Fluid Consumption (XP-h models only) |
0.76 liters per cycle
|
| Air inlet size |
3/4 npsm(f)
|
| Maximum air pressure supply to the system |
12 bar, 1 MPa
|
| Fluid pump inlets without hoppers |
1-1/4 in. npsm(m)
|
| Fluid gauge manifold outlets |
1/2 in. npt(f)
|
| Fluid mix manifold inlets |
1/2 in. npt(f) ball valves
|
| Mix manifold material outlet |
1/2 in. npt(f)
|
| Maximum feed pressure from remote source |
17 bar, 1.7 MPa
|
| Sound pressure |
7 bar, 0.7 MPa
|
| Sound power |
7 bar, 0.7 MPa
|
| Maximum Storage Time |
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
|
| Maximum Lifetime |
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
|
| Power Efficiency Factor (XP70) |
2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa)
|
| Air consumption per 1 gallon (3.78 l) of flow | |
| XP70 |
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
|
| XP50 |
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
|
| XP35 |
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
|
| Filtration | |
| Air inlet filtration |
40-micron filter/separator included
|
| XP pump outlets |
30 mesh
|
| XTR Spray Gun |
60 mesh
|
| Fluid Viscosity Range | |
| Gravity feed with 7 gallon (26 liter) hoppers |
200 to 20,000 cps (pourable)
|
| Pressure feed |
Any viscosity that will not require feed pressure more than 15% of outlet pressure
|
| Environmental Rating (Indoor/outdoor) | |
| Hazardous Areas |
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
|
| Ambient Temperature Range | |
| Operating |
4-54°C
|
| Storage |
-1-71°C
|
| Maximum Fluid Temperature |
71°C
|
| Wetted materials | |
| Housings and manifolds |
Carbon steel with electroless nickel plating
|
| Miscellaneous parts |
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
|
| Pump packings |
Carbon filled PTFE, proprietary UHMWPE
|
| Flush pump suction tube |
Aluminum
|
| Hoses |
Nylon core
|
| Weight | |
| Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers |
261 kg
|
| Full XP-h System with heaters, solvent flush pump, and hoppers |
273 kg
|
| Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers |
193 kg
|
| Bare XP-h System with no heaters, solvent flush pump, or hoppers |
204 kg
|
| XP35, XP50, or XP70 Pump only |
130 kg
|
| XP-h Pump only |
132 kg
|
| XP and XP-h Proportioners | |
| Maximum Fluid Working Pressure |
See Models section in instruction manual.
|
| Maximum Air/Hydraulic Oil Working Pressure |
See Models section in instruction manual.
|
| Combined Fluid Output (cc/cycle) |
See Models section in instruction manual.
|
| Pressure Ratio |
See Models section in instruction manual.
|
| Fluid Flow at 40 cpm |
See Models section in instruction manual.
|
| Hydraulic Fluid Consumption (XP-h models only) |
0.76 liters per cycle
|
| Air inlet size |
3/4 npsm(f)
|
| Maximum air pressure supply to the system |
12 bar, 1 MPa
|
| Fluid pump inlets without hoppers |
1-1/4 in. npsm(m)
|
| Fluid gauge manifold outlets |
1/2 in. npt(f)
|
| Fluid mix manifold inlets |
1/2 in. npt(f) ball valves
|
| Mix manifold material outlet |
1/2 in. npt(f)
|
| Maximum feed pressure from remote source |
17 bar, 1.7 MPa
|
| Sound pressure |
7 bar, 0.7 MPa
|
| Sound power |
7 bar, 0.7 MPa
|
| Maximum Storage Time |
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
|
| Maximum Lifetime |
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
|
| Power Efficiency Factor (XP70) |
2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa)
|
| Air consumption per 1 gallon (3.78 l) of flow | |
| XP70 |
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
|
| XP50 |
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
|
| XP35 |
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
|
| Filtration | |
| Air inlet filtration |
40-micron filter/separator included
|
| XP pump outlets |
30 mesh
|
| XTR Spray Gun |
60 mesh
|
| Fluid Viscosity Range | |
| Gravity feed with 7 gallon (26 liter) hoppers |
200 to 20,000 cps (pourable)
|
| Pressure feed |
Any viscosity that will not require feed pressure more than 15% of outlet pressure
|
| Environmental Rating (Indoor/outdoor) | |
| Hazardous Areas |
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
|
| Ambient Temperature Range | |
| Operating |
4-54°C
|
| Storage |
-1-71°C
|
| Maximum Fluid Temperature |
71°C
|
| Wetted materials | |
| Housings and manifolds |
Carbon steel with electroless nickel plating
|
| Miscellaneous parts |
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
|
| Pump packings |
Carbon filled PTFE, proprietary UHMWPE
|
| Flush pump suction tube |
Aluminum
|
| Hoses |
Nylon core
|
| Weight | |
| Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers |
261 kg
|
| Full XP-h System with heaters, solvent flush pump, and hoppers |
273 kg
|
| Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers |
193 kg
|
| Bare XP-h System with no heaters, solvent flush pump, or hoppers |
204 kg
|
| XP35, XP50, or XP70 Pump only |
130 kg
|
| XP-h Pump only |
132 kg
|
Ønsker du mer infomasjon om XP70-hf?
Send inn kontakt informasjonen din her, så tar vi kontakt med deg.
Takk - din melding er motatt.
Vi vil komme tilbake til deg så snart vi har sett på den.