Graco

Reactor E-10hp

Utvikle virksomheten din med polyurea-applikasjoner

Reactor E-10hp er et ideelt inngangssystem og er ideelt for beleggingsprosjekter som balkonger, bassenger, vanntett og bedliner-applikasjoner. Det er en smart, rimelig investering som vil hjelpe virksomheten din til å vokse.

Selv om det er et inngangssystem, har det fortsatt mye kraft. Reactor E-10hp gir høyt trykk for å gi deg kraft og ytelse du trenger for å spraye polyurea belegg. Denne kompakte enheten er lett og bærbar - og til og med går det på boligkraft, slik at du ikke trenger å investere i en generator.

Øk varmen for raske, 20-minutters oppstartstid.

Med systemets innovative boost varme og isolerte tanker, oppvarmes materialet raskt opp, slik at du går fort i gang. Faktisk er du klar til å spraye på en brøkdel av tiden, sammenlignet med over en times oppstartstid på en standard Reactor E-10.

Reactor E-10hp
Maximum fluid working pressure
20.6 MPa, 206 bar
Maximum spray pressure: 120 V
15.2 MPa, 152 bar
Maximum spray pressure: 230 V
17.2 MPa, 172 bar
Maximum fluid temperature
77°C
Maximum ambient temperature
48°C
Maximum output
3.8 liters/min
Output per cycle (ISO and RES)
0.014 liters/cycle
Air inlet
1/4 in. quick-disconnect industrial type pin fitting
Air outlet
1/4 npsm(m)
Overpressure relief
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
Gun compressed air requirements
Fusion Gun (purge air and operating air): 4 scfm (0.112 m³/min)
Maximum hose length
32 m
Tank capacity each (nominal)
22.7 liters
Weight (empty)
108 kg
<b >Recommended Mix Chamber Sizes
Fusion® Air Purge
000, AW2222 (00 and 01 at reduced spray pressure)
Probler® P2
AA (00 and 01 at reduced spray pressure)
<b >Electrical Requirements
120 V
120 VAC, 1 phase, 50/60 Hz, 3840 W; requires two separate, dedicated 20 A circuits. Full load peak amperage 16 A per circuit
230 V
230 VAC, 1 phase, 50/60 Hz, 5520 W; requires two separate, dedicated 15 A circuits. Full load peak amperage 12 A per circuit.
Generator Size
120 V
5000 W minimum
230 V
7500 W minimum
Heater Power
120 V
3000 W during recirculation, 2000 W during pressure spray mode
230 V
4000 W during recirculation, 2760 W during pressure spray mode
Sound Pressure
In fast recirculation mode
71.3 dB(A)
Measure at 2500 psi (17 MPa, 172 bar), 1 gpm (3.8 lpm)
85.6 dB(A)
Sound Power Sound power measured per ISO-9614-2.
In fast recirculation mode
79.9 dB(A)
Measure at 2500 psi (17 MPa, 172 bar), 1 gpm (3.8 lpm)
93.3 dB(A)
Fluid Outlets
ISO Side
-5 JIC male
RES Side
-6 JIC male
Fluid Circulation Returns
ISO side
-5 JIC male
RES side
-6 JIC male
Hose Markings
ISO side
Red
RES side
Blue
Wetted Parts
Wetted parts on all models
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
Reactor E-10hp
Maximum fluid working pressure
20.6 MPa, 206 bar
Maximum spray pressure: 120 V
15.2 MPa, 152 bar
Maximum spray pressure: 230 V
17.2 MPa, 172 bar
Maximum fluid temperature
77°C
Maximum ambient temperature
48°C
Maximum output
3.8 liters/min
Output per cycle (ISO and RES)
0.014 liters/cycle
Air inlet
1/4 in. quick-disconnect industrial type pin fitting
Air outlet
1/4 npsm(m)
Overpressure relief
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
Gun compressed air requirements
Fusion Gun (purge air and operating air): 4 scfm (0.112 m³/min)
Maximum hose length
32 m
Tank capacity each (nominal)
22.7 liters
Weight (empty)
108 kg
<b >Recommended Mix Chamber Sizes
Fusion® Air Purge
000, AW2222 (00 and 01 at reduced spray pressure)
Probler® P2
AA (00 and 01 at reduced spray pressure)
<b >Electrical Requirements
120 V
120 VAC, 1 phase, 50/60 Hz, 3840 W; requires two separate, dedicated 20 A circuits. Full load peak amperage 16 A per circuit
230 V
230 VAC, 1 phase, 50/60 Hz, 5520 W; requires two separate, dedicated 15 A circuits. Full load peak amperage 12 A per circuit.
Generator Size
120 V
5000 W minimum
230 V
7500 W minimum
Heater Power
120 V
3000 W during recirculation, 2000 W during pressure spray mode
230 V
4000 W during recirculation, 2760 W during pressure spray mode
Sound Pressure
In fast recirculation mode
71.3 dB(A)
Measure at 2500 psi (17 MPa, 172 bar), 1 gpm (3.8 lpm)
85.6 dB(A)
Sound Power Sound power measured per ISO-9614-2.
In fast recirculation mode
79.9 dB(A)
Measure at 2500 psi (17 MPa, 172 bar), 1 gpm (3.8 lpm)
93.3 dB(A)
Fluid Outlets
ISO Side
-5 JIC male
RES Side
-6 JIC male
Fluid Circulation Returns
ISO side
-5 JIC male
RES side
-6 JIC male
Hose Markings
ISO side
Red
RES side
Blue
Wetted Parts
Wetted parts on all models
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

Ønsker du mer infomasjon om Reactor E-10hp?

Send inn kontakt informasjonen din her, så tar vi kontakt med deg.